..
..
welcome once again to those that got their Tecno L3 BRICKED.
.
.
.
I Also Beleave with this some of us would be able to show appreciation
in one way or the other
.
.
AS STOCK ROM we about to install. its from my device so i recommend
we perform a device hardreset
after a SUCCESSFUL installation of this STOCK ROM,to enable us wipe
off all my junk files in this ROM.although nothing much but i'd advice
we do that to avoid stories that touch..hehehe..
.
so back to the SHOWROOM.
.
.
.
REQUIREMENTS:
-PC(not compulsary)
-Rooted Device(which means your device must be rooted before it got Bricked)
-Tecno L3 Device.
-Brain/Understanding
-CWMrecovery installed on your Device.
.
TUTORIAL HAS TWO PHASES.
IT Goes like this,if you dont have have CWMrecovery,then perfom PHASE2 of the tutorial before
coming to PHASE1,
PHASE 1
Now lets Get to the point. Since you'v Rooted your Device,
then i believe you have the posible knowledge of using SP FlashTOOL
.
.
1-Download The stock rom files
.
2-copy all the parts to a new folder in your PC
.
3-Click on Tecno_L3_Stock_ROMDump_By_Dmedalion.part01 .
it will automatically unpack all the remaining parts together.
after the unpack you should have this folder
130822-125557
.
4-Copy the above folder(130822-125557) to your
SDcard/Clockworkmode/backup/
.
5-Since your Device is Dead and Can still boot into Recovery MODE(CWMr)
.
6-Goto Backup & Restore and
.
7-Restore the folder(130822-125557).
wait for process to run through.after Restoration is complete.
REBBOT ur Device.....
.......................
.......................
.......................
.......................
.......................
.......................
If you have dont have CWMr.
then you need to flash one to ur Device befor performing this task.
to Do so,since your device can not boot,then you will
be needing SP Flashtool to Flash the CWMrecovery.img
to your Device,this will replace the recovery mode that came with
your device which is known as the Stock 3e Recovery
.....
.....
PHASE 2
FOR THE NOOBS: after installing CWMrecovery,this is what your Recovery mode should
look like when ever you press your power button+volume key.
....
....
TIP HOW TO FLASH THE RECOVERY FOR NOOBS
*copy the Recovery.img to any foleder on ur PC
(make sure its the pc u used in rooting ur device,or any other that has the MTK VCOMDrivers installed)
if its not any of these, then you might need to read the rooting
tutorial/how to install the MTK VCOM Drivers..so i wont be dancing around this aspect again.
....
....
Back to our story:
after copying the recovery.img to any Folder,Do the same to your MT6575_Android_scatter_emmc
1
.
*Launch SP Flashtool and click on Scatter-loading.
Locate the MT6575_Android_scatter_emmc you extracted earlier and choose it
2
.
*A list of Tecno L3 Map files should pop up,
when it shows up,click on RECOVERY then locate your recovery.img
file you extracted earlier and select it
3
4
.
.
After Selecting click on DOWNLOAD Tab,
4
it will give
you a warning that 'not all images were seleted',just ignore the message and click 'YES' To continue
...
Now since ur device is not booting,simply insert the battery and connect it via USB to the PC,then then
the flashing proccess should start,when successfull,you should see a DOWNLOAD OK
with a green circle,..
..
*
now try booting into recovery mode and you should see a new recovery mode like mine
above(first pic)
..
if this was done successfully,then you can procceed to INFO PHASE 1
0 comments:
Post a Comment